Wired and Bluetooth controllers answer different connection questions
The original GameSir G8 Galileo is the wired model in this comparison. GameSir describes the standard G8 Plus as a Bluetooth mobile controller. That distinction tells you how each controller establishes its gaming connection. It does not, by itself, identify every available charging route or establish room for an accessory on the back of a phone.
Key Takeaways
- A controller’s connection type does not establish rear clearance for a magnetic cooler.
- The G8 Galileo’s pass-through feature charges the phone conditionally, not an assumed second accessory.
- The K12’s PD 5V/3A requirement needs its own power plan before cables are routed.
- An assembled phone and case reveal grip and cable conflicts that a device-length range cannot.
To decide whether a wired or Bluetooth controller can accommodate phone charging and a K12, check the exact model’s connection and charging instructions, then test the assembled fit with your phone, case, controller, and cooler.
| Decision | Original G8 Galileo | Standard G8 Plus | KryoZon K12 |
|---|---|---|---|
| Established connection or attachment | Wired phone controller | Bluetooth phone controller | MagSafe or adhesive magnetic ring |
| Established power information | Conditional phone pass-through; maximum controller input of 9 V/3 A | Do not infer a charging function from its Bluetooth connection | Type-C power; PD 5V/3A supply required |
| Fit information to use | Check the assembled phone and controller | GameSir lists a 110–215 mm device-length range; check the assembled rear space | Check the intended magnetic mounting position and cable route |
Methodology: Manufacturer-stated specifications from the G8 Galileo manual page, G8 Plus product information and K12 product specifications. The available sources do not report test conditions for an assembled phone, controller and cooler.
Will your phone, controller and K12 fit—and how will each be powered? The G8 Plus device-length range concerns the device held by the controller; it does not measure free depth behind it. Likewise, the G8 Galileo’s input rating describes its documented charging arrangement, not an available power output for an accessory.
G8 Galileo pass-through charges the phone under stated conditions
The GameSir G8 Galileo manual-page FAQ describes conditional pass-through charging for the phone. It says the phone and charger must both support PD 2.0 or newer. GameSir states a maximum controller input of 9 V/3 A and says the controller can negotiate a maximum 9 V/3 A profile with the charger and phone. The power actually delivered to the phone remains subject to the phone’s system restrictions. The stated maximum is therefore not a promise that every attached phone will charge at that rate.
If you want to charge the phone while using this wired model, verify the phone and charger requirements before planning the rest of the setup. Then identify the cable intended for the controller’s documented pass-through arrangement. Treat that cable as part of the phone-charging path, not as an assumed source for a rear-mounted cooler.
Do not carry the G8 Galileo answer over to the standard Bluetooth G8 Plus. GameSir’s supplied G8 Plus information establishes its Bluetooth connection and device-length range, not a pass-through charging specification. If charging through a controller is essential to your layout, confirm that function for the exact controller model before relying on it. You can still compare physical fit without assuming that two similarly named controllers have the same charging path.
Cooler clearance is an assembled-phone measurement
GameSir lists a 110–215 mm compatible device-length range for the standard G8 Plus. Length tells you something useful about the devices its grip is designed to hold. It does not measure the gap behind a seated phone, the shape of the controller bridge, or the space needed by a cooler and cable. A phone that falls within a listed length range still needs a rear-space check with its actual case attached.
The KryoZon K12 Ultra-Light Magnetic Phone Cooler attaches using MagSafe or an adhesive magnetic ring. Its specified weight is 65g, and it uses semiconductor TEC cooling. Those are product specifications, not measurements of how it fits within either GameSir controller.
Make the rear-space check with the case you will use
Place the phone, with its everyday case if applicable, into the controller. Look at the intended magnetic mounting area from the side and rear. Hold the K12 at that point without forcing it against the controller bridge. Check whether the attachment area is accessible, whether the cooler touches a rigid controller surface, and whether your normal grip puts a finger where the cooler or its cable must sit. Repeat the check if you change cases; the relevant object is the assembled phone, not its bare dimensions on a listing.
Next, inspect the route out of the K12’s Type-C connection. A cooler can appear to have room when viewed straight from the back but leave no convenient path for its plug or cable once your hands wrap around the grips. Try the position you would actually use rather than judging from a product photograph.
The K12 cooler needs a separately planned power route

The K12 product specifications list Type-C power, a 15W (5V/3A) rating and a required PD 5V/3A charger. Plan a source that meets that stated requirement and a cable route to the mounted cooler. Its Type-C connection belongs to the cooler; the G8 Galileo’s documented pass-through arrangement belongs to the phone. Neither controller’s phone connection establishes that it can supply the K12.
A second path, if you want to charge the phone, runs through a charging method supported by the exact phone and controller arrangement you choose. A third path runs from the K12 to a supply meeting its own requirement.
Before selecting a layout, identify where each plug will end up after the phone is seated and the K12 is mounted. Leave enough slack for your ordinary grip and for placing the controller down without tugging either connection.
A complete cable layout must work in your hands
A rear-view fit check catches collisions with the controller bridge, but it can miss problems at the ends of the device. With the phone installed, locate its charging connection, the controller’s relevant connection, and the planned K12 cable. Check whether a plug can be inserted without pushing the phone out of position. Then hold the assembled setup as you would during play. A route that looks tidy on a desk may cross a finger position once both hands are on the grips.
Route cables without sharp bends or pinching them between the phone and controller. Set the assembled controller down and check that neither the cooler nor a connector bears its weight.
- Seat the phone: install the intended case and place the phone in the controller at its normal playing position.
- Establish the gaming link: confirm the wired connection for a G8 Galileo or the Bluetooth connection for a standard G8 Plus.
- Plan phone charging separately: if using G8 Galileo pass-through, check the documented PD conditions for the phone and charger.
- Position the cooler: check the magnetic attachment area, rear bridge, grip points and Type-C plug with the K12 in its intended position.
- Route each lead: identify a supply meeting the K12’s stated requirement, then hold and set down the assembled setup to check for interference.
The controller choice follows the assembled-fit check
Choose the original wired G8 Galileo when its direct controller connection suits your phone and its documented, conditional phone pass-through is part of your plan. Choose the standard G8 Plus when you want the Bluetooth connection it offers and your phone fits its stated device-length range. In both cases, the phone case, rear bridge, cooler position and power leads still have to coexist in the setup you will hold.
The K12’s mounting and power specifications do not establish clearance for your particular combination.
Product Specifications
| Model | Power | Noise | Weight | Cooling | Attachment | Port | Finish | Compatibility | Charger |
|---|---|---|---|---|---|---|---|---|---|
| KryoZon K12 Ultra-Light Magnetic Phone Cooler | 15W (5V/3A) | 32dB | 65g | Semiconductor TEC | MagSafe or adhesive magnetic ring | Type-C | Vacuum electroplating | iPhone / Android | PD 5V-3A required |
Frequently Asked Questions
Does the GameSir G8 Galileo charge a phone while playing?
GameSir describes conditional phone pass-through charging for the original G8 Galileo. It says both phone and charger must support PD 2.0 or newer, and actual delivered power depends on the phone’s system. Check those conditions for your phone and charger rather than treating the controller’s maximum input rating as a guaranteed phone charging rate.
Does the Bluetooth G8 Plus have the same pass-through charging feature?
The supplied GameSir G8 Plus information establishes a Bluetooth connection and a 110–215 mm device-length range; it does not establish the G8 Galileo’s pass-through feature for this model. Confirm a charging function in documentation for the exact controller before designing a phone-charging route around it.
Can the controller’s charging connection power the K12?
Do not assume it can. The K12 requires Type-C power from a PD 5V/3A charger, while GameSir’s G8 Galileo pass-through description concerns charging the phone. As a planning precaution, allow for a separate K12 power path unless the exact equipment documentation confirms another arrangement.
How can I check magnetic cooler clearance before buying?
Seat your phone and everyday case in the intended controller, then check the proposed magnetic attachment area against the rear bridge and your hand positions. Include the cooler’s Type-C plug and cable in the layout. The G8 Plus’s 110–215 mm device-length specification cannot replace that assembled rear-space check.
References & Citations
- The original wired G8 Galileo offers conditional phone pass-through charging; phone and charger must support PD 2.0+, maximum controller input is 9 V/3 A, and actual phone charging is system-dependent. (GameSir original wired G8 Galileo manual-page FAQ)
- The standard G8 Plus is a Bluetooth mobile controller with a stated compatible device-length range of 110–215 mm. (GameSir standard G8 Plus Bluetooth official platform and length)