If you are already planning a CPU repaste, the useful next step is to check what contacts the VRAM and what the lifted heatsink reveals—not to add pads to the shopping cart by default.
Key Takeaways
- A CPU repaste does not mandate replacing the VRAM filler.
- A tidy appearance does not establish reusability after heatsink removal.
- A borrowed 0.5 mm pad size does not establish LOQ fit.
- An exact model and opened assembly guide the material decision.

A 100°C complaint does not identify the material to replace
If your concern is a high reading, give the technician the HWiNFO log, the workload during the reading and the record of any earlier work. Ask which sensor produced the figure and whether the same complaint was present before service.
If your concern is instead that the heatsink must come off for a CPU repaste, that is a different decision. Removal creates an opportunity to inspect other contact areas; it does not make replacement of every material beneath the assembly automatic. Record what the technician finds before authorizing additional materials. A repair note that distinguishes the CPU die work from any VRAM work is more useful than a single instruction to “redo the thermals.”
Lenovo LOQ thermal putty choices start with the full model
“Lenovo LOQ” names a laptop family, not the particular assembly on your bench. The official LOQ 15IAX9 hardware maintenance manual gives CPU/GPU die thermal-interface instructions; its inspected section does not supply a VRAM pad thickness or reuse rule. Send the repairer the full model designation from your own machine and ask which contact areas and materials apply before ordering VRAM filler.
Keep the CPU and GPU dies distinct from VRAM and power-component contact points on the technician’s work list. The linked r/GamingLaptops post asks whether paste was applied to parts the poster believed required putty. That account raises a useful inspection question, but the user’s description cannot identify the factory material in your LOQ (r/GamingLaptops discussion). Ask for each material to be matched to its actual contact point rather than assuming one compound serves the entire assembly.
Product names can obscure that distinction. A LOQ 15IAX9 discussion illustrates the naming confusion: its PTM7950 listing used the phrase “thermal pads.” The word “pad” in a listing is not, by itself, an answer to what should fill a VRAM contact gap. Tell the technician the intended component and show them the exact listing before buying; do not substitute a product merely because its label sounds similar to the material named in a repair discussion.
LOQ thermal putty reuse is an inspection decision
Changing CPU paste does not automatically mean changing the material beside it. Equally, filler that looks tidy from above has not necessarily been assessed after the heatsink is lifted. Let the technician inspect the material on the components and the corresponding area of the heatsink before deciding whether it can remain, needs restoration or needs replacement.
Separated material needs a record before cleanup
The linked MSI Vector 17 HX discussion concerns a different laptop. Ask the repairer to photograph both sides before cleaning and assess reuse separately.
Before work starts, agree on how an unexpected finding will be handled: should the technician pause and contact you, or do they already have an appropriate replacement identified for this model? If no suitable material is available, a pause is preferable to improvising a thickness from an online recommendation. Request an itemized account afterward stating whether the VRAM material was left in place, restored or replaced. That record makes a later follow-up more precise than “the laptop was repasted.”
Pads require a fit decision, not a borrowed thickness

Assess a proposed pad against the actual VRAM contact and the heatsink’s assembled fit. Its product name alone cannot establish that fit.
The linked discussion concerns an MSI Vector 17 HX and a proposed 0.5 mm pad; it does not establish a Lenovo LOQ thickness.
Two easy assembly mistakes are worth checking
- Material at the wrong contact point: Have the repairer identify the component beneath each treated area before applying die paste or a gap filler. a specific Reddit thread of another laptop questioned paste found on parts they believed required putty (r/GamingLaptops discussion).
- A substitution chosen before a fit check: If pads are proposed, ask the repairer to compare the measured VRAM gap with the candidate material’s specified compression range, then record the selected material and thickness. Do not choose a pad thickness by guesswork.
A purchase sequence keeps the repaste focused
Before approving additional material, check these items with the repairer:
- Identify the laptop. Record its full LOQ model designation and give it to the technician. Do not purchase by the family name alone.
- Describe the job. State whether you are addressing a logged temperature complaint, arranging a CPU repaste, or both. Supply prior service notes and any relevant HWiNFO log.
- Check the model information. Ask the technician which service instructions apply and what those instructions say about the areas they plan to disturb.
- Document the opened assembly. Have them identify the die surfaces and the VRAM or power-component contact areas, then record the original material’s condition on both sides.
- Decide whether replacement is needed. Base that decision on the applicable information and what the technician actually finds, not on the CPU paste change alone.
- Choose and verify a substitute only then. If the repairer proposes putty or pads, ask how they will check suitability and assembled contact before the machine goes back into use.
If you must bring material to a repair appointment, ask the technician what information they need before you place an order. A product listing can answer what an item is; it cannot confirm an unseen gap in your laptop. Also ask whether the repair can proceed as a die-only job if the existing VRAM contact is judged suitable, and what the shop will do if inspection shows replacement is necessary but the proper material is unavailable. Those are concrete questions a technician can answer without a guessed thickness.
After reassembly, compare the original complaint with a similar workload and keep the service record.
External airflow cannot substitute for internal contact
A cooling pad is a separate choice from a VRAM putty-or-pad repair. If the LOQ runs sustained workloads after its internal assembly has been checked, external airflow may be worth considering for the desk setup. Assess desk airflow separately from internal VRAM contact and heatsink fit; ask the repairer to check those internal issues before considering a cooling pad.
For that separate use, the KryoZon H7 Semiconductor 8-Fan Laptop Cooling Pad has a TEC and eight-fan array, independent five-level controls, and a stated fit of up to 21 inches. Those are product specifications, not a test of this LOQ or a reason to postpone inspection of an internal contact problem. Check that your laptop sits appropriately on the pad and that its intake arrangement suits the setup before treating it as an option for sustained desk use.
For LOQ 15IAX9, the inspected CPU/GPU die-material section of Lenovo’s manual does not specify VRAM filler; have the technician identify that contact on your machine before ordering material.
Product Specifications
| Model | Cooling | Power | Temp Drop | Fan Speed | Controls | Lighting | Weight | Size | Fits | Material | Plug | Tilt |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| KryoZon H7 Semiconductor 8-Fan Laptop Cooling Pad | Semiconductor TEC + 8-Fan Array | 9V/3A (27W) DC adapter | 10 degree C | 3,200 RPM | Dual 5-level independent | RGB, 10 modes | 1,374g | 416x316x45mm | Up to 21 inch | ABS + Aluminum Alloy | DC5.5 | Adjustable |
Frequently Asked Questions
Do I need to replace VRAM putty when repasting a Lenovo LOQ CPU?
Not automatically. The inspected CPU/GPU die-material section does not specify whether VRAM filler should be reused or replaced. Decide from the exact opened assembly and its contact condition.
Can I reuse putty that looks fine after the heatsink comes off?
The Lenovo die-material section does not give a VRAM putty reuse test. Material left on both sides after removal is an observation; ask the repairer to assess whether contact can be restored on this assembly.
What thermal pad thickness should I buy for Lenovo LOQ VRAM?
Provide your complete LOQ model to the repairer. The linked discussion concerns an MSI Vector 17 HX and a proposed 0.5 mm pad; it is not a Lenovo LOQ thickness recommendation.
Will a laptop cooling pad fix a bad VRAM contact?
No external pad should be used as a substitute for checking a suspected internal contact issue. Address the assembly question with a technician first. Consider external airflow separately if you want to assess your setup during sustained use after the internal work is resolved.
References & Citations
- A buyer questioned whether paste had been applied at contact points believed to require putty on another gaming laptop. (Reddit r/GamingLaptops — material placement discussion)
- A LOQ 15iax9 owner encountered a PTM7950 listing described as thermal pads. (Reddit r/LenovoLOQ — PTM7950 listing discussion)
- An owner said they had changed paste without changing putty and doubted the untouched putty explained their result. (Reddit r/GamingLaptops — paste and putty discussion)
- An MSI owner described filler remaining on both mating surfaces and considered 0.5 mm pads while questioning gap variation; neither observation specifies a LOQ gap. (Reddit r/MSILaptops — putty and pad fit discussion)
- Lenovo LOQ 15IAX9 official Hardware Maintenance Manual — thermal interface handling
Community & User Sources
- When gaming I've seen my CPU temp reach over 90C. With fans on auto. And sides of the keyboard are hot to the touch. (Reddit User (Reddit))
- like just touching the top of my keyboard burn my fingers, when im not playing a ressource heavy game my pc sit at 67... (Reddit User (MSI) (Reddit))
- the gaming laptops now a days are not worth calling as Laptops anymore. You cant put them in you lap. It will burn yo... (Reddit User (Reddit))
- Just got a asus ROG zehpyrus G16 , just with the pc on at desktop screen it gets pretty damn hot on my legs if I'm on... (Reddit User (ASUS ROG) (Reddit))
- I went about my day when suddenly I went to grab my laptop and found it burningly hot. It was so hot that my fingers ... (Reddit User (Lenovo Legion) (Reddit))
- For reference I use Llano 12, it can lower temperatures at 10/15c degrees, but it is loud. It is ok if you use headph... (Reddit User (Reddit))
- I had the IETS GT600, which is similar to the ILLANO V10/V12 by design. Its VERY LOUD (sounds like an airplane when t... (Reddit User (Reddit))
- I'd say at max it's about as half as loud as a standard vacuum or a large fan. I usually keep it at 1200rpm and while... (Reddit User (Reddit))
- Bs2 pro, it's by FAR the quietest and most effective laptop cooler. Everything else from llano and IETS sounds like a... (Reddit User (Reddit))
- 1. No cooling pad : CPU 89°c GPU 70°c 2. Cooling pad on 1000rpm: CPU 78°c GPU 56°c 3. cooling pad on 2800rpm: CPU 72°... (Community Feedback)
- During max load on Battlefield 6, turbo mode + cpu boost, I was getting temperatures between 78-84 degrees on the cpu... (Community Feedback)
- CPU Temp in Time Spy: 93C With Cooling Pad (max): 82C GPU Temp: 73C With Cooling Pad (max): 63C (Community Feedback)
- My temps at idle went from 45C~ to 27C~ Playing games such as Fortnite, Battlefield 6, and COD at 1080p Ultra dropped... (Community Feedback)
- llano v10-12-13 (best cooling, loud, built in dust filter, most expensive, -10 degree difference) ... klim everest (n... (Community Feedback)
- The creator's hardware walk-through identifies four large fans, four smaller fans, the central thermoelectric plate, ... (Vladislav (Influencer))
- Creator-reported bench readings: 8.5 W, 10.7 W, 13.1 W, about 22 dB at the low setting, and approximately 32 to 33 W ... (Vladislav (Influencer))
- Creator-reported cold-plate reading: approximately 10.5 C after about two minutes, with room temperature described as... (Vladislav (Influencer))
- Creator-reported sequential results: Run 1 GPU/CPU 68/68 C; Run 2 GPU/CPU 64/65 C; Run 3 GPU mid-60s, CPU 68 C, monit... (Vladislav (Influencer))
- The final GPU display is summarized as mid-60s because the auto-captioned number is ambiguous. (Vladislav (Influencer))